Full Upper All on
5 implant case
with Freedom HD
and SNAP

The team in this case :
  • Quantum Creations – Sung Ho Kwon RDT
  • Dr. Daniel Fortino and Joseph Fortino
The equipment in this case :
  • 3D scanner – Freedom HD
  • Face scanner – SNAP
  • Design software – exocad
  • CAM software – Millbox
  • Milling system – Sharp2 Plus
  • Angle Correction with Dynamic solution
  • Bio horizons Multi unit implants
  • Vita YZ HT zirconium block with Vita YZ HT shading liquid
  • Build up with VM9 series porcelain
  • Stain with Vita AKZENT PLUS WITH AKZENT FINISH Agent.
  • VM 9 =Effect enamel4, and Opal 1, 2, NT, ENL
  • Contour bake
Full Upper All on 5 implant case with my dental friends.
 
Patient had been using Denture for 30 years and she couldn’t smile because she didn’t like her look with her denture on, so she really wanted to get her confident smile back.
 
Dr. Daniel Fortino placed 5 implants on upper. Dr. Joseph and I put fixed bridge on same day.
A few month later, Dr. Joseph took impression with Verification Jig which is the most important process.
According to the conversion denture, I delivered Prototype to check the bite relations and midline, the Dr. Joseph said it was way off.
I wanted to get more information on chairside to verify the midline, so I used the DOF SNAP face scanner in order to get more accurate information for final restoration.
After the visit there was a small mistake, I made during the PMMA stage. I fixed the midline according to what I checked on chairside instead of following the face scan guide.
For the final restoration, I fixed the midline according to the face scan guide and after that case was simply done.
 
Finally, I could deliver the case to the patient.
Patient was simply happy with her natural smile and that was just priceless.
 
With the simple mistake I made this time I learned my lesson and I think I can do much better job with my new digital workflow.

Model Scanner

Freedom HD

Full Upper All on
5 implant case
with Freedom HD
and SNAP

The team in this case :
  • Dental technician from OOO – Sungho Kwon
  • Dr. Daniel Fortino & Dr. Joseph
The equipment in this case :
  • 3D scanner – Freedom HD
  • Face scanner – SNAP
  • Design software – exocad
  • CAM software – Millbox
  • Milling system – Sharp2 Plus
  • Angle Correction with Dynamic solution
  • Bio horizons Multi unit implants
  • Vita YZ HT zirconium block with Vita YZ HT shading liquid
  • Build up with VM9 series porcelain
  • Stain with Vita AKZENT PLUS WITH AKZENT FINISH Agent.
  • VM 9 =Effect enamel4, and Opal 1, 2, NT, ENL
  • Contour bake
Full Upper All on 5 implant case with my dental friends.
 
Patient had been using Denture for 30 years and she couldn’t smile because she didn’t like her look with her denture on, so she really wanted to get her confident smile back.
 
Dr. Daniel Fortino placed 5 implants on upper. Dr. Joseph and I put fixed bridge on same day.
A few month later, Dr. Joseph took impression with Verification Jig which is the most important process.
According to the conversion denture, I delivered Prototype to check the bite relations and midline, but the Dr. Joseph said it was way off.
I wanted to get more information on chairside to verify the midline, so I used the DOF SNAP face scanner in order to get more accurate information for final restoration.
After the visit there was a small mistake, I made during the PMMA stage. I fixed the midline according to what I checked on chairside instead of following the face scan guide.
For the final restoration, I fixed the midline according to the face scan guide and after that case was simply done.
 
Finally, I could deliver the case to the patient.
Patient was simply happy with her natural smile and that was just priceless.
 
With the simple mistake I made this time I learned my lesson and I think I can do much better job with my new digital workflow.

Model Scanner

Freedom HD

Contact us